How to maintain belt filter machine ,belt sludge filter dewatering and sludge filter machine ?
General rules of maintaining belt filter machine and belt sludge filter dewatering
1.Belt filter machine and belt sludge filter dewatering must be designated by a person to use and maintain
2.Before starting the filter press in each shift, the operator carefully checks the lubrication conditions of the lubrication points and the fastening conditions of the parts to ensure that the whole machine is well lubricated and clean and tidy.
3. All parts with speed regulating devices, Speed at zero or low speed when starting, turn off to zero or low speed; mechanical speed regulator is not allowed to adjust at shutdown.
4. Careful protection of motor and electrical equipment, Do not allow sludge or water into the motor and control box.
5. To avoid accidents,not allow to place any tools on Filter belt and in the machine
Daily maintain for belt filter machine and belt sludge filter dewatering and sludge filter machine
1.When the filter press starts, the operator will stick to his post ,pay attention to the working condition of the filter press at any time, whether there is abnormal noise or smell: whether there is any debris entering the sludge pump or filter press; whether the filter cloth cleanness is normal,
2.Check the water level in the air compressor gas water separator and the oil level in the oil mist separator on each shift, release water and add lubricating oil in the condition of no pressure if necessary.
3.After each shift work, Operator:
4.Wash the compressor (including all accessories) inside and outside, ensure filter cloth clean, inside and outside clean, clean site, ensure no mud, dirt.
5.Use wooden scraper to clean the scraper plate, And clean down.
6. Scrubbing the flocculant and medicine tools.
Weekly maintain for belt filter machine and belt sludge filter dewatering and sludge filter machine
1.Sludge metering pump, flocculant metering pump, filtrate pump part:
2.Check sludge metering pump, flocculant metering pump and driving part, To solve the abnormal condition of leakage (mud) and drive device.
3.Check the effluent and leakage of filtrate pump.
4.Wash the equipment of mixing and dilution of flocculant; clean the diffuser of flocculant (if used).
Air compressor part:
1.Check the oil level , add sufficient if insufficient.
2.Discharge condensate from gas tank.
3.Clean air filter.
4.Manual check the function of air compressor valve.
How to maintain belt filter machine ,belt sludge filter dewatering and sludge filter machine ?
All rolling bearings are filled with calcium or lithium grease;
Drive gear with calcium base grease;
Guide roller slide, Lubricating grease.
Bracket for belt guide and tensioning cylinder and lubricating oil for U ring pin.
Check filtrate box and bottom tank in drain and pressure zone, Wash the deposited sludge.
Check the rubber water seal on each rotating shaft and reset if necessary.
Check the belts status
Monthly maintain for belt filter machine and belt sludge filter dewatering and sludge filter machine
1. All driving motors are inspected ,mostly temperature rise and soundTo the control box for a full-system functional inspection.
Quarterly maintain for belt filter machine ,belt sludge filter dewatering and sludge filter machine
1. Check the production capacity of air compressor.2. bearings of Belt conveyor roller be added lubricating oil.
Yearly Maintain for belt filter press, sludge dewatering belt filter press, sludge filter press
Replacement of air compressor oil.
2.Replacement of motor gear box oil.
Check filtrate pump rotary bearings, Refill grease.
4.Check all bearings of filter press, replace grease.
The moisture content of the filter cake is about 20-65% by Ambang environmental belt filter press, sludge dewatering belt filter press and sludge filter press. The sludge after dewatering can be dried or packed and transported. Filtered clean water can be recycled or discharged naturally.
We have professional equipment manufacturers, with more advanced mechanical processing equipment and experimental equipment. Strict management, excellence, design, manufacturing level continues to improve. In order to meet the needs of our customers, our latest developed belt filter press, sludge dewatering belt filter press, sludge filter press, the technology is leading in China.
Meibang Environmental protection equipment co.,ltd.
Office Add:Centre of Building Minggao,No 123,Yingbing Road,Huadu Disctrict
,Guangzhou,Guangdong
24 hours hotline：Miss Li 139 2623 5580
Factory Add:Meibang Industrial Park,No. 40 Dabu Road,Huadu Disctrict,Guangzhou,Guangdong